OPEN ACCESS 
PEER-REVIEWED
Surface Roughness and Deformation Effects on the Behaviour of a Magnetic Fluid Based Squeeze Film in Rotating Curved Porous Circular Plates
1Birla Vishvakarma Mahavidyalaya Engineering College, Vallabh Vidyanagar, Anand, Gujarat (India)
2Department of Mathematics, Sardar Patel University, Vallabh Vidyanagar, Anand, Gujarat (India)
Abstract
The combined effect of surface roughness and bearing deformation on the magnetic fluid lubrication of a squeeze film between two rotating transversely rough porous circular plates has been investigated. The results indicate that the bearing performance gets adversely affected by the surface roughness, bearing deformation combination, even if, a magnetic fluid has been considered as the lubricant. However, the negatively skewed roughness introduces a better performance for a good range of deformation by suitably choosing the curvature parameters. It is appealing to note that, although there are several factors bringing down the load carrying capacity, still the bearing can support a good amount of load even when there is no flow unlike, the case of conventional lubricants. In addition, this article also emphasizes the role of rotation for improving the bearing performance.
At a glance: Figures
Keywords: circular plates, magnetic fluid, roughness, deformation, rotational inertia, load carrying capacity
American Journal of Marine Science, 2015 3 (1),
pp 1-10.
DOI: 10.12691/marine-3-1-1
Received December 03, 2014; Revised January 30, 2015; Accepted February 02, 2015
Copyright © 2015 Science and Education Publishing. All Rights Reserved.Cite this article:
- Shimpi, M. E., and G. M. Deheri. "Surface Roughness and Deformation Effects on the Behaviour of a Magnetic Fluid Based Squeeze Film in Rotating Curved Porous Circular Plates." American Journal of Marine Science 3.1 (2015): 1-10.
- Shimpi, M. E. , & Deheri, G. M. (2015). Surface Roughness and Deformation Effects on the Behaviour of a Magnetic Fluid Based Squeeze Film in Rotating Curved Porous Circular Plates. American Journal of Marine Science, 3(1), 1-10.
- Shimpi, M. E., and G. M. Deheri. "Surface Roughness and Deformation Effects on the Behaviour of a Magnetic Fluid Based Squeeze Film in Rotating Curved Porous Circular Plates." American Journal of Marine Science 3, no. 1 (2015): 1-10.
| Import into BibTeX | Import into EndNote | Import into RefMan | Import into RefWorks |
1. Introduction
It was Archibald [1] who studied the squeeze film performance between various geometrical configurations of the flat surfaces. In [2], Prakash and Vij used the well known Morgan-Cameron approximation for a squeeze film between porous plates considering the porous facing thickness to be small enough, while the inertia effects induced by rotation were significant with higher rotational speed and small squeeze velocity. Wu [3] modified the analysis of Wu [4] to develop the Reynolds equation for the effect of rotation.
Murti [5] presented the squeeze film performance in curved circular plates describing the film thickness by an exponential expression. The investigation was based on the assumption that the central film thickness was constant unlike the minimum film thickness as considered by Hays [6]. Vora and Bhat [7] studied squeeze film behaviour between a curved upper plate with a porous facing and an impermeable flat plate taking rotation in to account. This investigation suggested that rotation of plates turned in an adverse effect on the performance of the bearing system. Ajwaliya [8] modified the above analysis by considering the lower plate also to be curved.
Normally, most of the theoretical investigations deal with squeeze film behaviour assuming that the bearing surfaces are perfectly rigid. But, under high loads the bearing may deform producing wedge effects in the lubricant film there by, altering the squeeze. Ramanaiah and Sundarammal [9] studied the effect of bearing deformation on the squeeze film character between circular and rectangular plates. It was established that the bearing deformation reduced the load carrying capacity and increased the squeeze. Muhsin [10] discussed the effect of elastic deformation of bearing surfaces and analyzed the steady state performance of offset halves bearing. It was shown that elastic deformation had a considerable influence on the performance especially, at higher eccentricity values.
Verma [11] studied the magnetic fluid lubrication of squeeze films and established its superiorely over conventional lubricant based squeeze films. Bhat and Deheri [12] investigated the effects of magnetic fluid lubricant on the action of squeeze film in curved porous circular disks, considering the method of Verma [11]. Chandra and Sinha [13] considered Ferrofluid lubrication of externally pressurized circular plates and conical bearings. It was observed that the effect of applied transverse magnetic field as well as Brownian time relaxation parameter was negligible on load carrying capacity.
Bhat and Deheri [14] investigated the performance of magnetic fluid based squeeze film in porous annular disks which was developed by Bhat [15] to study the effect of magnetic fluid lubricant on the squeeze film performance between porous rotating circular plates in the presence of an external magnetic field oblique to the lower plate. Patel and Deheri [16] studied the squeeze film behaviour between curved circular plates lying along the surfaces determined by the secant function under the presence of a magnetic fluid lubricant. Lin et al [17] studied the effects of couple stresses resulting from the lubricant blended with various additives upon the squeeze film behavior between a long cylinder and a plane surface were analyzed. It was concluded that compared to the conventional Newtonian lubricant case, the couple stress effects characterized by the couple stress parameter signify an improvement in the squeeze film characteristics. Hsu et al [18] investigated the squeeze film characteristics between rotating circular disks with an electrically conducting lubricant in the presence of transverse magnetic field. It was concluded that, on the whole the use of electrically conducting fluid in the presence of a transversely magnetic field resulted in an improvement of performance characteristics in rotating circular disks. Shah and Bhat [19] dealt with the Ferrofluid squeeze film between curved annular plates considering rotation of magnetic particles. It was found that load carrying capacity increased when volume concentration of the solid phase, Langrin’s parameter or the curvature of the upper plate were increased. Lu et al [20] discussed the fluid inertia effect in magneto-hydrodynamic annular squeeze films. It was shown that the inertia correction factor in the magneto-hydrodynamic load carrying capacity was more pronounced with large Hartmann numbers.
Many methods were proposed to deal with the effect of surface roughness on the squeeze film performance characteristics. Tzeng and Saibel [21] adopted a stochastic approach to model the random roughness which in turn, was modified and developed by Christensen and Tonder [22, 23, 24] to study the effect of surface roughness in general. A number of investigations deployed the stochastic model of Christensen and Tonder to study effect of surface roughness [Ting [25], Prakash and Tiwari [26], Gupta and Deheri [27]]. Prajapati [28] investigated the squeeze film performance in rotating porous rough circular plates with elastic deformation modifying slightly the approach of Christensen and Tonder [22, 23, 24]. Hsu et al [29] observed the combined effect of surface roughness and rotational inertia on squeeze film performance between parallel circular disks. Davim [30] discussed about the performance of the hydrodynamic rough bearing which also examined tribology aspects with special emphasis on surface topography, wear of materials and lubrication.
Deheri et al [31] analyzed the behaviour of magnetic fluid lubrication of squeeze film between transversely rough curved plates. It was shown that the load carrying capacity increased with increasing magnetization. Although, the effect of transverse roughness was adverse in general, negatively skewed roughness resulted in a little better performance.
Ram et al [32] analyzed the effect of porosity on revolving Ferrofluid flow in rotating disk using Neuringer-Rosenwig model. It was found that the influence of rotation of fluid flow was not that significant on the displacement thickness of fluid layer. Huang et al [33] studied the effect of Ferrofluid lubrication under the presence of an external magnetic field. It was proved that the Ferrofluid had a good friction reduction performance in the presence of an external magnetic field compared with the carrier liquid and that its life period could be greatly improved.
Shimpi and Deheri [34] discussed the combined effect of surface roughness and deformation on the performance of a magnetic fluid based squeeze film between rotating curved porous circular plates. It was shown that the negatively skewed roughness resulted in a improved performance in spite of the adverse effect of porosity and deformation. However, for an overall improved performance, deformation deserved to be minimized even if a suitable magnetic strength was in force.
Lu and Deng [35] considered squeeze flow analysis of magnetorheological Fluids in parallel circular disks. The effect of slip coefficient and power law inertia on the flow field and squeeze force were discussed. Raoa et al [36] obtained a generalized form of Reynolds’ equation for two symmetrical surfaces considering velocity slip and viscosity variation for the lubrication of the squeeze film between the circular plates. The load carrying capacity and squeezing time were found to be decreased due to the slip.
In spite of the fact that the transverse surface roughness introduced an adverse affect in general, the studies carried out by Vadher et al [37], Shimpi and Deheri [38] and Deheri et al [39] revealed that the negatively skewed roughness registered a relatively better performance. Therefore, it was thought appropriate to deal with the effect of surface roughness and bearing deformation on the squeeze film performance in curved porous rotating circular plates under the presence of a magnetic fluid lubricant.
2. Analysis
The geometry and configuration of the bearing system is shown in Figure 1, which consists of the circular disks.
PowerPoint Slide
Larger image(png format)
Both the disks are assumed to be elastically deformable and their contact surfaces are considered to be transversely rough. The upper disk moves towards the lower disk normally with uniform velocity 
. Both the disks are assumed to have transversely rough surfaces.
Normally the following assumptions are made:
1) The viscosity remains constant and the flow is laminar.
2) There are no external forces acting on the lubricant.
3) The lubricant film thickness is very small in comparison with the dimension of the bearing.
4) Fluid inertia is small compared to viscous forces.
5) Velocity gradients across the film predominate.
6) The porous region is homogeneous and isotropic while the flow in the porous region is governed by Darcy’s law.
7) Pressure and normal velocity component are continuous at the interface.
8) Zero leakage occurs within the operating specification.
9) Particles are not generated by wear.
10) Heat generated is almost negligible.
In view of the discussions regarding stochastic modeling of the roughness adopted by Christensen and Tonder [21, 22, 23] and Prajapati [28] the film thickness is assumed to be
 | (1) |
wherein 
denotes the smooth and unstressed part of the film thickness and 
is the part due to surface roughness measured from the mean level 
and its random character is expressed by the variable 
. 
is governed by the probability density function
 | (2) |
where 
is the maximum deviation from the mean film thickness. The mean 
, the standard deviation 
and the parameter 
, which is the measure of symmetry of the random variable 
, are defined by the relationships
 | (3) |
and
 | (4) |
where 
denotes the expected value defined by
 | (5) |
It is assumed that the upper plate lying along the surface determined by
 | (6) |
approaches with normal velocity 
, to the lower plate lying along the surface
 | (7) |
where 
is the central distance between the plates, 
and 
are the curvature parameters of the corresponding plates. The central film thickness 
then is defined by [Bhat [15]]
 | (8) |
Assuming axially symmetric flow of the magnetic fluid between the annular plates under an oblique magnetic field
 | (9) |
whose magnitude 
is a function of 
vanishing at 
, the angle of inclination 
of the magnetic field as in Bhat [15]. Now the modified Reynolds equation governing the film pressure 
takes the form [Prajapati [40], Bhat and Deheri [14], Gupta and Deheri [27], Vadher et al [37]]
 | (10) |
with
 | (11) |
 | (12) |
and
 | (13) |
where 
is permeability of free space, 
is the magnetic susceptibility of particles and 
is the viscosity of the lubricant, 
is the permeability of porous facing, 
is the thickness of porous medium, 
is the local elastic deformation of the porous facing and 
is the reference ambient pressure and 
is a suitably chosen constant to suit the dimension and strength of the magnetic field.
In view of the following non-dimensional quantities,
 | (14) |
(
being density of lubricant and 
the angular velocity)
integrating the stochastically averaged Reynolds Equation (11) under the boundary conditions
 | (15) |
one obtains the expression for the non-dimensional pressure distribution as
 | (16) |
where
 | (17) |
 | (18) |
 | (19) |
 | (20) |
 | (21) |
and
 | (22) |
The load carrying capacity in dimensionless form then, is calculated as
 | (23) |
which leads to
 | (24) |
where,
 | (25) |
 | (26) |
 | (27) |
 | (28) |
3. Results and Discussion
It is observed that the pressure distribution and the load carrying capacity in dimensionless form are obtained from Equation (16) and Equation (24) respectively. Also, It can be seen from these equations that the non-dimensional pressure distribution and the load carrying capacity are decided by several parameters such as 
and 
. It is noticed that for porous bearing with smooth surfaces this investigation gets reduced to the study of Bhat and Deheri [12] considering with the magnetic fluid based squeeze film between circular plates in the absence of rotation and deformation.
Further, taking the magnetization parameter 
to be equal to zero for a nonporous bearing with smooth surfaces, one can find the results of Prakash and Vij [2] when no rotation and deformation are involved. Moreover, setting the magnetization parameter to be equal to zero for a porous bearing with smooth surfaces one can obtain the results of Bhat [15] in the absence of deformation.
It is noticed from Equation (16) that the non-dimensional pressure increases by
 | (30) |
while the dimensionless load carrying capacity gets enhanced by
 | (31) |
as compared to the case of conventional lubricant. It is easily observed that 
is linear with respect to
as a result, higher values of 
may provide increased load carrying capacity. Also, it is noticed that bearing deformation significantly alters the profile of the pressure distribution. It is seen that, the effect of the transverse surface roughness is, in general, adverse. Probably, this may be due to the fact that the roughness of the bearing surfaces retards the motion of the lubricant resulting in reduced load carrying capacity. The elastic deformation further makes this negative effect more significant.
For the graphical representation the following fixed values are taken it to consideration
 |
Figure 2 - Figure 9 giving the variation of load carrying capacity with respect to the magnetization parameter indicate that load carrying capacity increases due to the magnetic fluid lubricant, and this increase is more in the case of standard deviation and rotational inertia. The effect of skewness on the load carrying capacity with respect to
appears not that significant.
and
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and
PowerPoint Slide
Larger image(png format)A closed scrutiny of these Figures reveals that the performance of the bearing system registers an improved performance. However, variance (negative) induces an increase in the load carrying capacity, while negatively skewed roughness marginally increases the load carrying capacity. Further, the curvature parameters increase the load carrying capacity similar to the case of circular plates as discussed in Shimpi and Deheri [39].
The profile of the distribution of dimensionless load carrying capacity with respect to the standard deviation associated with roughness is depicted in Figures 10-14. It is evident that the standard deviation adversely affects the performance of the bearing system in the sense that the load carrying capacity decreases considerably due to the standard deviation. However, this decrease is relatively more in the cases of rotational inertia. In other words, the combined effect of standard deviation, rotational inertia and deformation turns in significantly reduced load carrying capacity there by, adversely affecting the bearing system.
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)It is also observed that the decreased load carrying capacity due to standard deviation gets further decreased owing to porosity. It is revealed that for larger values of deformation, this negative effect is more crucial.
The distribution of non- dimensional load carrying capacity with respect 
can be obtained from form Figure 15 – Figure 18. It is clearly seen that 
(positive) decreases the load carrying capacity while 
(negative) introduces an increase in the load carrying capacity. The effect of deformation on distribution of the load carrying capacity with respect to 
is quite significant. In addition, the effect of rotational inertia on the distribution of load carrying capacity with respect to variance (positive) is equally significant.
and 
PowerPoint Slide
Larger image(png format)
and
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)The effect of skewness on the profile of the load carrying capacity given in Figure 19 – Figure 21 indicates that the skewness follows almost the trends of variance. This also proves that the combined effect of negatively skewed roughness and negative variance is quite significant from the bearing design point of view. Further more, it is interesting to note that the effect of the deformation with respect to skewness is significant. The fact that, the porosity effect on the distribution of load carrying capacity is considerably adverse that can be obtained from the Figure 22 – Figure 23. One can easily infer that the decrease in the load carrying capacity due to porosity is crucial when considered with the case of bearing deformation. In addition, larger values of deformation make this negative effect of porosity quite crucial for the bearing design. Figure 24 underlines that the rotational inertia decreases the load carrying capacity.
and 
PowerPoint Slide
Larger image(png format)
and
PowerPoint Slide
Larger image(png format)
and
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)
and 
PowerPoint Slide
Larger image(png format)Lastly, Figure 25- Figure 26 presenting the variation of the load carrying capacity with respect to the curvature parameters make an interesting scenario in the sense that the load carrying capacity increases sharply with increase in 
when lower values of 
are involved. Besides, the trends of the load carrying capacity with respect to the curvature parameters are opposite to that of the investigation of Shimpi and Deheri [33].
Some of the Figures witnessed here tend to indicate that the combined adverse effect of 
and 
is more pronounced especially when larger values of deformation are involved. It is noticed that the negative effect of porosity, standard deviation and rotational inertia can be minimized up to some extent by the positive effect of the magnetic fluid lubricant in the case of negatively skewed roughness, particularly, when negative variance occurs. It is observed that the effect of the bearing deformation becomes more and more significant when large values of rotational inertia are involved.
Lastly, the combined effect of standard deviation and porosity remains considerably adverse for a good amount of range of deformation parameter.
and 
PowerPoint Slide
Larger image(png format)
and
PowerPoint Slide
Larger image(png format)In this type of bearing system even the lower to moderate values of rotational inertia may provide a enhanced performance for a large range of deformation.
A critical review of the graphs presented in Vadher et al [37], in comparison with the graphs of the present investigation suggests that the load carrying capacity is relatively less increased here so far as the combined effect of skewness and variance is concerned [cf. Figure 27].
and
PowerPoint Slide
Larger image(png format)Furthermore, a comparison of present investigation with the results of Deheri et al [38] tells that even the load carrying capacity is less increased here so far as the effect of porosity and standard deviation are concerned [cf. Figure 28].
and
PowerPoint Slide
Larger image(png format)Also, a critical study of the results of Shimpi and Deheri [39] together with the conclusions of the current study reveals that the combined effect of rotation and deformation leads to a decrease in the load carrying capacity here. It is seen that the curvature parameters present a relatively better performance here as compared to the squeeze film behaviour discussed in Patel and Deheri [16] in the absence of rotation and deformation.
A close look at the current investigation indicates that the load carrying capacity is comparatively more here with regard to the discussion of Hsu at el [18] while the effect of deformation is also significant. It can be observed that the effect of the roughness is almost identical with that of Hsu at el [29] for small values of rotational inertia.
4. Conclusion
It is seen that in this type of bearing system, the effect of bearing deformation is quite significant unlike the study of quite Shimpi and Deheri [34]. It is studied that the positive effect of magnetization can be obtained by considering the following combination of the parameters:
 |
It is found that hydrodynamic effect tends to reduce the adverse effect of roughness and porosity. Due to the positive effect of negatively skewed roughness, the presence of bearing deformation makes it mandatory that the roughness must be accounted while designing the bearing system even if curvature parameters, rotational parameter and magnetic strength are appropriately considered. It is needless to say that this article suggests an additional degree of freedom from design point of view.
Acknowledgements
The authors acknowledge with thanks, the comments and suggestions of the reviewers/ editor, leading to an improvement in the presentation.
References
| [1] | Archibald, F.R, “Load capacity and time relations for squeeze films”, Transaction ASME, 78, A 231-245, 1956. | ||
 In article | |||
| [2] | Prakash, J. and Vij, S.K, “Load capacity and time height relation between porous plates”, Wear, 24: 309-322, 1973. | ||
| In article | CrossRef | ||
| [3] | Wu, H, “The Squeeze film between rotating porous annular disks”, Wear, 18, 461-467, 1971. | ||
| In article | CrossRef | ||
| [4] | Wu, H, “Squeeze film behaviour for porous annular disks”, Journal of Lubrication Technology, 92, 206-209, 1970. | ||
| In article | CrossRef | ||
| [5] | Murti, P.R.K, “Squeeze Films in curved circular plates”, Transaction ASME, F97, 650-656, 1975. | ||
| In article | |||
| [6] | Hays, D.F, “Squeeze films for rectangular plates”, ASME, 58, 243-251, 1963. | ||
| In article | |||
| [7] | Vora, K.H. and Bhat, M.V, “The Load capacity of a squeeze film between curved porous rotating circular plates”, Wear, 65, 39-46, 1980. | ||
| In article | CrossRef | ||
| [8] | Ajwaliya, M.B, “On certain theoretical aspects of lubrication”, Dissertation, Sardar Patel University, Vallabh Vidyanagar (India), 1984. | ||
| In article | |||
| [9] | Ramanaiah, G. and Sundarammal, A, “Effect of bearing deformation on the characteristics of a slider bearing”, Wear, 78, 273-278, 1982. | ||
| In article | CrossRef | ||
| [10] | Muhsin, I.A, “The effect of elastic deformation of bearing surface on the steady state performance of offset halves bearing”, Nahrain University, College of Engineering Journal (NUCEJ), 12 (2), 122-128, 2009. | ||
| In article | |||
| [11] | Verma, P.D.S, “Magnetic Fluid-Based Squeeze Film”, International Journal of Engineering Science, 24 (3), 305-401, 1986. | ||
| In article | CrossRef | ||
| [12] | Bhat, M.V. and Deheri, G.M, “Magnetic fluid based squeeze film in curved porous circular disks", Journal of magnet and magnet materials, 127, 159-62, 1993. | ||
| In article | |||
| [13] | Chandra, P. and Sinha, P. “Ferrofluid lubrication of externally pressurized circular plates and conical bearings”, International Journal of Engineering Science, 31 (4), 593-604, 1993. | ||
| In article | CrossRef | ||
| [14] | Bhat, M.V and Deheri, G.M, “Squeeze film behaviour in porous annular disks lubricated with magnetic fluid”, Wear, 152, 123-128, 1991. | ||
| In article | CrossRef | ||
| [15] | Bhat, M.V, “Lubrication with a magnetic fluid”, Team Spirit Pvt. Ltd India, 2003. | ||
| In article | |||
| [16] | Patel, R.M., and Deheri, G.M, “An analysis of magnetic fluid based squeeze film between curved circular plates”, Journal of National Acad. of Mathematics, 16, 74-84, 2002. | ||
| In article | |||
| [17] | Jaw-Ren Lin, J.R., Won-Hsion Liao, W.H. and Hung, C.R. “The effects of couple stresses in the squeeze film characteristics between a cylinder and a plane surface, Journal of Marine Science and Technology, 12 (2), 119-123, 2004. | ||
| In article | |||
| [18] | Hsu, C.H., Lai, C. Hung, C.R. and Lin, J.R, “Magneto-hydrodynamic squeeze film characteristics between circular discs including rotational inertial effects”, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 222 (2), 157-164, 2008. | ||
| In article | CrossRef | ||
| [19] | Shah, R.C. and Bhat, M.V, “Ferrofluid squeeze film between curved annular rotation of magnetic particles”, Journal of Engineering Mathematics, 51 (4), 317-324, 2005. | ||
| In article | CrossRef | ||
| [20] | Lu, R.F., Chien, R.D. and Lin, J.R, “Effects of fluid inertia in magneto-hydrodynamic annular squeeze films”, Tribology International, 39 (3), 221-226, 2006. | ||
| In article | CrossRef | ||
| [21] | Tzeng, S.T. and Saibel, E, “Surface roughness effect on slider bearing lubrication”, Transaction ASLE, 10, 334-342, 1967. | ||
| In article | |||
| [22] | Christensen, H., and Tonder, K.C, “Tribology of rough surfaces: stochastic models of hydrodynamic lubrication”, SINTEF Report No. 10/69, 1969a. | ||
| In article | |||
| [23] | Christensen, H., and Tonder, K.C, “Tribology of rough surfaces: parametric study and comparison of lubrication models”, SINTEF Report No. 22/69, 1969 b. | ||
| In article | |||
| [24] | Christensen, H., and Tonder, K.C, “The hydrodynamic lubrication of rough bearing surfaces of finite width”, ASME-ASLE Lubrication Conference: Paper no. 70, 1970. | ||
| In article | |||
| [25] | Ting, L.L, “Engagement behaviour of lubricated porous annular disks”, Wear, 34, 159-182, 1975. | ||
| In article | CrossRef | ||
| [26] | Prakash, J., and Tiwari, K, “Roughness effects in porous circular squeeze-plates with arbitrary wall thickness”, Journal of Lubrication Technology, 105, 90-95, 1983. | ||
| In article | CrossRef | ||
| [27] | Gupta, J.L. and Deheri, G.M, “Effect of roughness on the behavior of squeeze film in a spherical bearing”, Tribology Transaction, 39 99-102, 1996. | ||
| In article | CrossRef | ||
| [28] | Prajapati, B.L, “Behaviour of squeeze film behaviour between rotating porous circular plate: surface roughness and elastic deformation effects”, Journal of Pure and Applied Mathematical Science, 33(1-2), 27-36, 1991. | ||
| In article | |||
| [29] | Hsu, C.H., Lu, R.F. and Lin, J.R, “Combined effects of surface roughness and rotating inertia on the squeeze film characteristics of parallel circular disks”, Journal of Marine Science and Techno. 7 (1), 60-66, 2009. | ||
| In article | |||
| [30] | Davim, P.J, “Tribology for Engineering – A practical guide”. WP, Oxford-Cambridge-Philadelphia-New Delhi, 2011. | ||
| In article | |||
| [31] | Deheri, G.M., Patel, R.M. and Abhangi, N.D, “Magnetic fluid based squeeze film between transversely rough curved plates”, Advanced Tribology, 54-55, 2010. | ||
| In article | |||
| [32] | Ram, P., Sharma, K. and Bhandari, A, “Effect of porosity on revolving Ferrofluid flow with rotating disk”, International Journal of Fluids Engineering, 3 (3), 261-271, 2011. | ||
| In article | |||
| [33] | Huang, W., Cong, S. and Liao, S, “Study of the Ferrofluid lubrication with an external magnetic field”, Tribology Letters, 41, 145-151, 2011. | ||
| In article | CrossRef | ||
| [34] | Shimpi, M.E. and Deheri, G.M, “Surface roughness and deformation effect on the performance of a squeeze film in rotating curved porous circular plates with a magnetic fluid lubricant”, Journal of Tribology and Surface Engineering, 3-4, 175-195, 2011. | ||
| In article | |||
| [35] | Lu, G.P. and Deng, G.H, “Squeeze flow analysis of magnetorhelogical fluids between two parallel disks”, Journal of Chongqing University of Technology (Natural Science), 2011-12, 2012. | ||
| In article | |||
| [36] | Raoa, R.R., Gouthamia, K. and Kumarb, J.V, “Effects of velocity slip and viscosity variation squeeze film lubrication of two circular plates”, Tribology in Industry, 35 (1), 51-60, 2013. | ||
| In article | |||
| [37] | Vadher, P.A., Vinodchandra, P.C., Deheri, G.M. and Patel, R.M, “Behaviour of hydromagnetic squeeze film between two conducting rough porous circular plates”, Journal of Engineering Tribology, 222 (part J), 569-579, 2008. | ||
| In article | |||
| [38] | Deheri, G.M., Patel, H.C. and Patel, R.M, “Behaviour of magnetic fluid based squeeze film between porous circular plates with porous matrix of variable thickness”, International Journal of Fluid mechanics, 34 (6): 506-514, 2007. | ||
| In article | |||
| [39] | Shimpi, M.E. and Deheri, G.M, “Surface roughness and elastic deformation effects on the behaviour of the magnetic fluid based squeeze film between rotating porous circular plates with concentric circular pockets”, Tribology in Industry, 32 (2), 21-30, 2010. | ||
| In article | |||
| [40] | Prajapati, B.L, “On certain theoretical studies in hydrodynamic and electromagneto hydrodynamic lubrication”, India: PhD Thesis Sardar Patel University, Vallabh Vidyanagar, 1995. | ||
| In article | |||
CiteULike
Mendeley
StumbleUpon
Delicious
Facebook
Twitter
LinkedIn
Print