Article Versions
Export Article
Open Access Peer-reviewed

Acceptance and Re-verification Test of Length Metroscope

Tatiana Kelemenová1, Michal Kelemen1,, Miková Lubica1, Ivan Virgala1, Vladislav Maxim1, Tomáš Lipták1, Milan Lorinc1

1Faculty of Mechanical Engineering, Technical University of Kosice, Kosice, Slovakia

American Journal of Mechanical Engineering. 2014, 2(7), 274-277. DOI: 10.12691/ajme-2-7-21
Published online: August 25, 2017

Abstract

Paper deals with acceptance and re-verification of length measuring metroscope. The metroscope has been used very frequently for exercises in subject – Engineering Metrology at the bachelor study. New systematic errors have been obtained from calibration process. Other measurements have been also realized and corrections of results have been executed via using of new systematic errors. Measured errors from acceptance test have confirmed that metroscope is out of the limits defined through the maximum permissible error. Nevertheless the metroscope is fully functional and errors could be eliminated through the including of new measuring system consisting from suitable distance sensor.

Keywords:

metrology, measurement, systematic error, gauge blocks
[1]  Rabinovich, S. G., Measurement Errors and Uncertainties. Theory and Practice. Springer . 3rd ed. 2005, XII, 308 p.
 
[2]  Rabinovich, S. G.. “Accuracy of single measurements”. Accreditation and Quality Assurance, August 2007, Volume 12, Issue 8, pp 419-424.View Article 
 
[3]  Schwenkea, H., Knappb, W., Haitjemac, H., Weckenmannd, A., Schmitte, R., Delbressine, F., “Geometric error measurement and compensation of machines-An update”, CIRP Annals-Manufacturing Technology. Volume 57, Issue 2, 2008, Pages 660-675.View Article 
 
[4]  Chunovkina, A.G., “Terminology. Measurement Error, Measurement Uncertainty, Measurand Uncertainty”. Measurement techniques, Vol. 43, No. 7, 2000, pp. 581-586.View Article 
 
[5]  Sartori, S., Zhang, G.X., “Geometric Error Measurement and Compensation of Machines”, CIRP Annals-Manufacturing Technology, Volume 44, Issue 2, 1995, Pages 599-609.View Article 
 
[6]  John R. Taylor, An Introduction to Error Analysis: The Study of Uncertainties in Physical Measurements, 2d Edition, University Science Books, 1997.
 
[7]  Philip R. Bevington and D. Keith Robinson, Data Reduction and Error Analysis for the Physical Sciences, 2d Edition, WCB/ McGraw-Hill, 1992.
 
[8]  , S., “A Beginner's Guide to Uncertainty of Measurement”, The National Physical Laboratory is operated on behalf of the DTI by NPL Management Limited, a wholly owned subsidiary of Serco Group plc. Measurement Good Practice Guide No. 11 (Issue 2), August 1999.
 
[9]  Chudy, V., Palencar, R., Kurekova, E., Halaj, M., Measurement of technical quantities. STU Publishing, 1st. edition, 1999. PubMed 
 
[10]  Kreith, F., The Mechanical Engineering Handbook Series. CRC PRESS. .
 
[11]  JCGM 200-International vocabulary of metrology-Basic and general concepts and associated terms (VIM) 3rd edition (2008 version with minor corrections). © JCGM 2012 Available online: http://www.iso.org/sites/JCGM/VIM-JCGM200.htm
 
[12]  JCGM 104-Evaluation of measurement data-An introduction to the "Guide to the expression of uncertainty in measurement" (ISO/IEC Guide 98-1). First edition July 2009. Available online: http://www.bipm.org/en/publications/guides/gum_print.html
 
[13]  Doiron, T., Beers, J., The Gauge Block Handbook, Dimensional Metrology Group, Precision Engineering Division, National Institute of Standards and Technology, 1995, Monograph (NIST MN), 145 pages.
 
[14]  Duchoň, F., Hanzel, J., Babinec, A., Rodina, J., Pásztó, P., Gajdošík, D., “Improved GNSS Localization with the Use of DOP Parameter”, In: Applied Mechanics and Materials.-ISSN 1660-9336.-Vol. 611 (2014), pp. 450-466.
 
[15]  Pyszko, R., Koval, L., Machackova, A., Kleckova, Z., Jedlicka, Z., “Embedded control system of apparatus for measurement of thermal conductivity”, Proceedings of the 7th WSEAS International Conference on Automatic Control, Modeling and Simulation, (2005), pp. 113-117.
 
[16]  Wilhelm, R.G., Hocken, R., Schwenke, H., „Task Specific Uncertainty in Coordinate Measurement”, CIRP Annals-Manufacturing Technology, Volume 50, Issue 2, 2001, Pages 553-563.View Article 
 
[17]  Dovica, M., Zivcak, J., Kelemenová, T., Measurement of geometric quantities in mechanical engineering, Technical University of Kosice Publishing, 1st edition, 2011, 290 pages.
 
[18]  Koniar, D. Hargaš, L. Hrianka, M., “Measurement of Object Beating Frequency Using Image Analysis”, Applied Electronics 2009, Internal Conference, Pilsen, 9-10 September 2009, IEEE Catalog Number CFP0969A-PRT.
 
[19]  Dekan, M., Duchoň, F., Jurišica, L., Vitko, A., “Probabilistic Model of Laser Rangefinder”. In: AD ALTA: Journal of Interdisciplinary Research .-Vol. 1, Iss. 2 (2011), pp. 151-155.
 
[20]  Dovica, M., Kelemenová, T., Henriczyová, T., Coordinate metrology, 1st edition, publisher: Technical University od Kosice, 2012, 483 pages.
 
[21]  Busch, K., Kunzmann, H., Wäldele, F.: “Calibration of coordinate measuring machines”, Precision Engineering, Volume 7, Issue 3, July 1985, Pages 139-144.View Article 
 
[22]  Koniar, D., Hargaš, L., Hrianka, M., Špánik, P., “Application of DICOM Standard in LabVIEW Environment”, In: Sensors & Transducers Journal, Vol. 87, Issue 1, January 2008, pp. 19-23.
 
[23]  Vitko, A., Jurišica, L., Babinec, A., Duchoň, F., Kľúčik, M., “Resolution of Robot Kinematic Redundancy as a Problem of Adaptive Control”, In: AT&P Journal Plus.-ISSN 1336-5010.-No. 1: Systems of Automatic Control (2010), pp. 58-61.
 
[24]  Acko, B., “Calibration of measuring instruments on a coordinate measuring machine”, Advances in Production Engineering & Management 2 (2007) 3, pp. 127-134.